How to Install Metal Stair Nosings on Vinyl Plank Flooring

Vinyl plank staircases bring together the best of both worlds: the affordability and easy upkeep of synthetic materials, along with the style and beauty of wood, stone, or marble. As good as it is, however, it may not stand up to heavy traffic as well as other staircase materials - and that's where metal nosings come in.

Strong and durable, metal nosings are able to shield your stairs from daily wear and tear far better than vinyl or wood nosings. They'll never chip, peel, or rot, and will provide a slip-resistant surface that improves safety overall. They're especially useful in commercial and industrial spaces, but you can easily add them to your home staircase for that extra layer of safety.

Installing metal stair nosings on vinyl plank stairs is a fairly straightforward task when you follow the right steps. Read on for our step-by-step guide to the whole process, from gathering your materials to adding the finishing touches!

1. Prepare Your Supplies

Before you get started, it's best to have all your tools and materials ready to go. You'll need to gather the following:

• Metal stair nosings (preferably aluminium)
• Measuring tape
• Pencil
• Adhesive or construction adhesive
• Screws or nails
• Screwdriver or hammer
• Sandpaper
• Cloth for cleaning
• Saw (optional)
• Mitre box and saw (optional)
• Utility knife (optional)

Always remember to wear personal protective equipment (such as safety goggles) throughout construction, especially if or when you're cutting metal.

2. Measure and Cut the Nosing

Use your tape and pencil to carefully measure the width of your stairs, then determine the exact length of the metal stair nosing you'll need. Saw the metal stair nosing to the required length. If your stairs have corners, consider using a mitre box and saw for precise angle cuts.

If you're not confident with cutting metal or just want to make your life easier, you can instead choose to have your metal pre-cut by a reliable supplier like Clickmetal. They'll expertly cut your metal based on your measurements, saving you the trouble and cost of buying cutting equipment if you don't already have it, as well as the time it takes to do the cutting yourself.

3. Check Your Stairs

Double check your vinyl plank flooring is properly installed on the stair treads. Leaving too much overhang can make it difficult to install the nosing and create a trip hazard, so make sure the flooring is firmly attached to the treads according to the manufacturer's instructions, and use a utility knife to neatly trim any excess material flush with the edge of each tread.

4. Position and Secure the Nosing

You're now ready to start attaching your stair nosings to your stairs! Begin by applying construction adhesive to the back of one of your metal stair nosings, always following the manufacturer's instructions for the adhesive you're using.

Next, carefully place the metal stair nosing onto the edge of the stair, making sure it's aligned properly and covers the vinyl plank flooring. Press down firmly to bond the nosing to the stairs. If needed, use screws or nails to secure the nosing in place. Place them along the edge and at regular intervals. Be sure not to over-tighten the screws or nails, as this can damage the nosing or the vinyl planks underneath.

5. Clean and Smooth the Nosing

For a polished and clean finish, use sandpaper to smooth out any rough edges or excess adhesive that might have oozed out, and remove any adhesive residue from both the nosing surface and the vinyl plank flooring.

6. Allow to Dry

Repeat the steps above for each stair on your staircase.

Once you're happy with how the nosings fit onto your stairs, follow the manufacturer's suggestions for letting the adhesive dry and cure. It's best to leave it for at least 24 hours to be sure.

After the adhesive has completely dried, your metal nosings will be securely in place, offering both protection and a stylish finish for your stairs!

Premium-Grade Metal Nosings, Custom-Cut for Your Staircase

If you're looking to save yourself the time, hassle, and cost of cutting your own nosings, why not reach out to the team at Clickmetal? With over 70 years of industry know-how, we're experts in cutting high-quality aluminium nosings to your exact specifications. We offer a wide range of styles and thickness options to suit your needs, so no matter what kind of pieces you're looking for, you can count on our team to make them a reality.

We're also committed to delivering your components to your doorstep as swiftly as we can. We make it our goal to process all orders for dispatch within 3-5 working days from when we receive them, and then ship them out using a 24-hour (next working day) courier service. You'll have them ready to go in no time!

Get the exact pieces your project needs, quickly and without fuss. Buy custom-cut aluminium nosings from Clickmetal today!